6 Ryobi Backpack Blower Problems You Should Know About

The Ryobi Backpack Blower is a powerful blower featuring cruise control and changeable speed options. This powerful 2-cycle backpack blower comes with 175 MPH speed and 760 CFM.

Speed issue, engine refusing to start, engine flooding, smoke coming out, problems with cold start, and low power are the most common Ryobi Backpack Blower problems.

In this article, I’ll go through a few standard Ryobi Backpack Blower troubleshooting methods. So let’s begin by reviewing some of this blower’s characteristics and features.

Features & Specifications of Ryobi Backpack Blower:

Type	Gas-Powered
Throttle Position	Tube
Weight	18 lbs.
Engine Displacement	42 CC
Cruise Control	Yes
Noise Rating	73.4 dB
CFM	760
Strokes	2
Fuel Tank	38 Ounces

Common Ryobi Backpack Blower Problems and Solutions

Problems with Ryobi Backpack Blower	Solutions
Speed Issue	Adjust the mentioned screws properly.
Engine Refusing to Start	Test the spark plug.
Engine Flooding	Follow the instructions.
Smoke Coming Out	Clean the air filter and use proper lubricant fuel mixture.
Problems with Cold Start	Follow the proper method of cold starting.
Low Power	Clean the muffler and exhaust port.

1. Speed Issue

The blower will eventually turn itself off when you turn it on with a cold start. But soon, it will start functioning after a few tries as the fuel gets warmer.

But when it can’t accelerate fully, a problem arises. The blower will struggle to accelerate when you press the throttle.

The Fix

To resolve this problem, you must tweak the Ryobi Backpack Blower’s carburetor.

Check the blower’s speed by rotating the L-screw in the opposite direction. You must further crank the L-screw if you observe that the throttle response is sluggish.

You can also slightly rotate the idle screw in a clockwise manner. The problem should be resolved by following this procedure.

2. Engine Refusing to Start

Sometimes, the Ryobi Backpack Blower will refuse to start. The engine not starting properly will cause this issue.

The main reasons for this problem are not getting a spark, an improper amount of fuel, or a flooded engine.

The Fix

You must inspect the spark if there isn’t any. Place the spark plug on the steel tube after removing it and replacing the spark plug cover. Pull the wire at this point and look for a spark at the spark plug tip.

Continue the test with a replacement spark plug if there is no spark. You must press the primer bulb until it is filled with fuel if there is no fuel.

The principal fuel supply system is inhibited if the bulb does not fill. Primer bulb filling indicates a potential engine flood.

3. Engine Flooding

If the engine of the Ryobi Backpack Blower floods, it may show difficulty to start.

Sometimes, you can make it start, and sometimes, it may not respond properly. Also, the starter rope may seem stiffer making you have to give more force to pull it.

The Fix

Allow the machine to sit for 30 minutes if the engine is flooded. Choke should be positioned to run. Keep the gas pedal down while pulling the starter.

Replace the spark plug and attempt to restart the engine if the unit still won’t start after 15 pulls.

If the starter rope seems stiffer than usual, you should take the product in for service.

4. Smoke Coming Out

While blowing out leaves, you might notice that there is smoke coming out of the openings of the Ryobi Backpack Blower.

This happens when the engine produces smoke and cannot reach the top speed.

If the air filter is clogged and has not been cleaned for a while, this issue will occur. Also, improper lubricant fuel mixtures can produce a cloud of smoke.

The Fix

If the air filter is dirty, you can disassemble the blower. Now, clean the dirt and debris around the air filter. But if you don’t know your way around the blower, you should contact a professional.

If the lubricant fuel mixture is not correct, you have to implement a clean fuel and 2-cycle lubricant mixture.

5. Problems with Cold Start    

When you try to start the blower with a cold engine for the first time, it may refuse to start.

It may also start and then die on you suddenly. So, you should know how to properly cold start the Ryobi Backpack Blower.

The Fix

First, set the switch to power on. Then, you have to push the primer bulb 15 to 15 times. When the fuel fills up the bulb, you have to turn off the cruise control lever.

Now, position the choke lever to the cold start option and pull the starter grip. Pull it a couple of times to start the engine.

Now, set it to a warm start and do the same procedure again. After the engine starts, you should let it run for a minute. Then, you should use the blower.

6. Low Power

If you notice that you are not getting enough power from your Ryobi Backpack Blower, there might be a problem with the exhaust port.

If the muffler or the exhaust port is dirty, the blower will have a hard time powering up to its potential.

The Fix

You have to clean the port and muffler to fix this issue. These parts can collect carbon deposits.

Open the backpack blower and reveal the muffler and exhaust port. Use a brush and some pieces of clothing to clean the parts properly.

Frequently Asked Questions (FAQs)

Conclusion

In this post, I’ve covered the six most frequent Ryobi Backpack Blower problems. Fix the problems following the precise instructions.

The Ryobi backpack blowers are less problematic than the handheld models. So you should encounter these issues less frequently if you can maintain the product periodically.

Related Posts:

• 4 Most Common Ryobi Electric Leaf Blower Problems (Solutions Added)
• What Are The Most Common Ryobi 18V Leaf Blower Problems & How To Fix Them?
• 6 Ryobi 40V Blower Troubleshooting Techniques to Consider
• Ryobi 2 Cycle Blower Problems and Their Fixes
• 6 Husqvarna 150BT Problems that You Should Know About